以粉末冶金製備富鈦TiNi形狀記憶合金及其變態性質之研究

Powder Metallurgy Fabricated Ti-rich TiNi Shape Memory Alloys and Their Transformation Behavior Study

廖姚晴(Yau-Ching Liau)

指導教授 ： 吳錫侃

國立臺灣大學/工學院/材料科學與工程學研究所/碩士(2010年)

https://doi.org/10.6342/NTU.2010.10486

摘要

以粉末冶金(PM)製備富鈦TiNi形狀記憶合金，於900℃以下之溫度燒結時，因Kirkendall Effect於Ni粒附近留有≦5μm之孔洞，當在900℃持溫1小時後，因共晶反應使原本的Ti粒處形成大約20~50μm之孔洞，但Ti55.08at%-Ni者因有多量的Ti2Ni於高溫時成為液相，可將孔洞補平。PM Ti50at%-Ni於900℃以下燒結時，其變態溫度較同成份之VAR製備者高，且與PM Ti52at%-Ni和PM Ti55.08at%-Ni者相近，此應與其內均是富鈦TiNi B2相有關；當燒結溫度提升至1000℃以上時，PM Ti50at%-Ni的變態溫度則下降至比VAR者低，此應與TiNi B2相已由偏富Ti變為偏富Ni有關，且此時會固溶較多之C、O原子。在不同燒結流程的研究中，使用兩階段燒結法之Ti50at%-Ni的試片，相較於一階段燒結法，其密度可提升約10%，主因於900℃持溫2小時時，Ti和Ni間會先形成Ti2Ni、TiNi和TiNi3等中間相，因此再升溫至942℃時，其共晶反應不如一階段燒結者激烈。二階段燒結之Ti50at%-Ni其形狀回復率只有76%，較同成份VAR之90%小，應為PM試片中有許多孔洞之故。使用兩階段燒結法燒結之Ti52at%-Ni試片，相較於一階段燒結者，其密度可從76%提升至97%，其形狀回復率因有較多Ti2Ni相而為70%，但與同成份VAR者相近，但經5次之形狀回復測試後其回復率可達97%。PM Ti52at%-Ni的tanδ之峰值較同成分VAR者略大，顯示PM試片中的孔洞有助於吸收震動之能量。本文同時由Ti-Ni二元平衡圖，對富鈦TiNi形狀記憶合金之變態溫度常在出現M*≒60℃，A*≒100℃之現象提出解釋。

關鍵字

TiNi形狀記憶合金 ； 粉末冶金 ； 燒結機制 ； 顯微組織 ； 變態溫度

並列摘要

Martensitic transformation behaviors of Ti-rich TiNi shape memory alloys (SMAs) fabricated by powder metallurgy (PM) are investigated. When sintering at ＜900℃, PM SMAs have small pores(≦5μm) formed near Ni particles due to Kirkendall Effect, but sintering at 900℃ for 1 h, they have big pores(20~50μm) formed at the prior site of Ti particles due to eurtectic reaction. Ti55.08at%-Ni contains lots of Ti2Ni which becomes liquid phase at 984℃ and fills up the pore. As sintering at ＜900℃, the forward and reverse transformation peak temperatures (M* and A*) of PM Ti50at%-Ni are higher than those of VAR one, but similar to those of Ti52at%-Ni and Ti55.08at%
-Ni due to the formation of Ti-rich TiNi B2 phase. As sintering at ＞1000℃, M* and A* of PM Ti50at%-Ni are lower than those of VAR one due to the formation of Ni-rich TiNi B2 phase in which lots of carbon and oxygen atoms are dissolved simultaneously. Different sintering processes are also examined in this study. The density of Ti50at%-Ni sintered by 2-step process is 10% higher than that sintered by 1-step process. Because Ti2Ni, TiNi and TiNi3 are formed in Ti-rich PM SMAs during the holding time at 900℃, the eutectic reaction in 2-step process is not so violent as that in 1-step process. The shape recovery of PM Ti50at%-Ni is 76% which is lower than that of VAR one, 90%, due to the pores existed in PM alloy. Ti52at%-Ni alloy’s density sintered by 2-step process is 20% higher than that sintered by 1-step process, but its shape recovery (70%) is near to that of VAR one (72%) due to both have lots of Ti2Ni and the PM alloy has high density (92%). The damping capacity (tanδ) of PM Ti52at%-Ni is higher than that of VAR Ti52at%-Ni due to the pores in PM alloy can absorb the damping energy. In this study, PM Ti-rich TiNi SMAs exhibit M*≒60℃ and A*≒100℃ and this characteristic is explained from the viewpoint of Ti-Ni phase diagram.

並列關鍵字

Ti-rich TiNi shape memory alloys ； powder metallurgy ； sintering process ； microstructure ； transformation temperatures

參考文獻

1. L. C. Chang and T. A. Read, Trans. AIME., 189, (1951), 47.

2. T. Tadk, K. Otsuka and K. shimizu, Ann. Rev. mater. Sci, 18, (1988), 25.

3. H. Kessler and W. Pitsch, Acta Met. 15, (1967), 401.

6. T. Saburi and S. Nenno, Scripta Metall. 8, (1974), 1363.

9. L. Delaey and J. Thienel, in : Shape Memory Effects in Alloys, (J. Perkins, ed.), Plenum Press, New York, (1975), 341.