鐵-25鉻-6鎳-2.5銅合金相變化

Phase Transformations of the Fe-25Cr-6Ni-2.5Cu Alloys

林鳳耀(Feng-Yao Lin)

指導教授 ： 趙志燁

國立屏東科技大學/工學院/機械工程系所/碩士(2009年)

https://doi.org/10.6346/NPUST.2009.00277

摘要

摘要
學號: N9632003
論文題目：鐵–25鉻–6鎳–2.5銅合金相變化 總頁數：54 頁
學校名稱：國立屏東科技大學 系 (所) 別：機械工程系
畢業年月：2010年1月 學位別：碩士學位
研究生：林鳳耀 指導教授：趙志燁 博士
論文摘要內容：
本文主要探討鐵–25%鉻–6%鎳2.5％銅合金鑄件相變化，研究結果顯示：合金鑄件經1050℃/1小時高溫處理後，其顯微組織為沃斯田鐵（γ）與肥粒鐵（α）雙相結構，其中γ相晶格常數a=3.61Å，α相晶格常數a=2.86Å。另外，γ相可觀察到具有兩種方向關係的退火雙晶，分別為：[011]//[011]，(111)//(111)，以及[011]//[014]，(200)//(221)。合金鑄件經1050℃/1小時後，以及400~750℃短時間(8小時內)時效處理後，並無析出物被觀察到。延長時效時間12小時以上，於400~550℃時，於γ相或在α/γ邊界，可發現細微ε相與 M23C6相析出，其相變化為γ→γ+ε+M23C6，其中ε相晶格常數為a＝3.65Å，M23C6相晶格常數為a=10.65Å。而於600~750℃時，則觀察到γ→γ+ MC + M23C6相變態，其中，MC相晶格常數a=4.30Å。由於，晶粒邊界碳化物的析出，而導致合金鑄件硬度上升與延性下降。

關鍵詞：沃斯田鐵、肥粒鐵、ε相、M23C6

關鍵字

沃斯田鐵 ； 肥粒鐵 ； ε相 ； M23C6

並列摘要

Abstract
Student ID: N9632003
Title of Thesis: Phase Transformations of the Fe-25Cr-6Ni-2.5Cu Alloys
Total Pages: 54
Name of Institute: National Pingtung University of Science and Technology
Name of Department: Department of Mechanical Engineering
Date of Graduation: .January, 2010 Degree Conferred: Master
Name of Student: Feng-Yao Lin Adviser: Dr. Chih-Yeh Chao
The Contents of Abstract in this Thesis:

The main purposes of the present studies are to analyze the phase transformations of the Fe-25Cr-6Ni-2.5Cu cast alloy. Based on the present studies, some results are described as following. Being solution treatment 1050℃ for 1 hour, the microstructure of the alloy are a mixture of austenite and ferrite duplex phase. The lattice parameter of austenite and ferrite phase are a=3.65Å and a=2.86Å, respectively. In addition, some annealing twin is observed within austenite matrix. The orientation relationship of these twin are found as [011]//[011], (111)//(111), or [011]//[014], (200)//(221).
After being solution treatment at 1050℃ for 1 hour then aged at in the range of the 400 and 750℃ for a short time( below 8 hours), no precipitates are found neither the grain boundary or within the matrix. Increasing the aged time to 12 hours or above, a phase transition,γ→γ + ε + M23C6, is found within the γ matrix or on the were α/γ grain boundary when aged at temperature in the range between 400 and 550℃. The lattice parameter ofεand M23C6 phase are a=3.65Å and a=2.86Å, respectively. Moreover, when aged at 600~750℃,a phase transition,γ→γ + MC + M23C6, is found. The lattice parameter of MC phase is a=4.30Å. Due to the precipitation on the grain boundary, the hardness of the ally cast increases and of ductile decreased.

Keyword: austenite, ferrite,εphase, MC carbide, M23C6 carbide

並列關鍵字

austenite ； ferrite ； εphase ； MC carbide ； M23C6 carbide

參考文獻

4. M.O. Speidel, “Stress corrosion cracking of stainless in NaCl solutions”，Metall. Trans. A 12A（1981）779.

7. T.H. Chen and K.L. Weng and J.R. Yang, “The effect of high-temperature exposure on the microstructural stability and toughness property in a 2205 duplex stainless steel”, Materials Science and Engineering A338, （2002）, 259-270.

8. Michael Pohl and Oliver Storz and Thomas Glogowski,“Effect of intermetallic precipitations on the properties of duplex stainless steel”, Materials Characterization 58, （2007）, 65-71.

9. J.M. Pardal, S.S.M. Tavares, M. Cindra Fonseca, J.A. de Souza, R.R.A. Corte and H.F.G. de Abreu, “Influence of the grain size on deleterious phase precipitation in superduplex stainless steel UNS S32750”, Materials Characterization 60, （2009）,165-172.

10. E. Angelini *, B. De Benedetti, F. Rosalbino, “Microstructural evolution and localized corrosion resistance of an aged superduplex stainless steel”, Corrosion Science 46 ,(2004) ,1351–1367.