- 學位論文
抗EMI無電鍍銅聚丙烯腈高分子奈米複合材料之製備與研究
The Manufacture and Investigation of Electroless Copper Deposited Polyacrylontrile (PAN) Nano Composites for EMI Shielding
摘要
摘要 本研究是藉由高分子表面金屬複合化來達到電磁波遮蔽功能，因此利用無電鍍法(化學鍍法)製備導電聚丙烯腈薄膜作為電磁波遮蔽材以達到電磁波遮蔽功能，並且使Cu31S16化合物析鍍於表面上以及因擴散使銅離子在PAN內部成核為Cu2-xS化合物。另外無電鍍進行前，PAN不須經敏化活化為本實驗之特色。 本實驗是以銅離子濃度與膨潤處理做為影響高分子奈米複合材之抗電磁波遮蔽值(EMI SE)變化的兩大變數。再利用FE-SEM、AFM、HR-TEM、HP-XRD、EDS、DSC等分析，探討表面與截面之微觀型態、奈米顆粒擴散的情形以及熱性質影響等等，而解釋高分子奈米複合材料抗電磁波遮蔽值之變化，另外還對其做抗菌性質的檢測。 由實驗結果顯示，所有試片皆通過ASTM D3359黏著性測試，且在析鍍溫度95℃及析鍍時間1小時，以CuSO4Na2S2O3NaHSO3 (2/1/1)組成進行析鍍，電磁波遮蔽值可達到約為18dB~20dB。如果再經過膨潤處理後，聚丙烯腈複合薄膜之電磁波遮蔽值則可達到約為30dB~35dB。由HP-XRD分析得知，聚丙烯腈薄膜在經過無電鍍銅處理後，析鍍上Cu31S16金屬層以及部分因氧化而形成的氧化銅。再經由AFM表面微觀分析發現，原本平整表面的聚丙烯腈薄膜，經過無電鍍處理後，表面變成凹凸不平，因此可以進一步證明銅硫合金已析鍍在聚丙烯腈表面上。從FE-SEM表面以及破斷面圖中可以觀察到析鍍顆粒形狀為不規則形狀以及針狀結構且鍍層厚度最厚約為200nm。藉由EDX、HR-TEM等分析可以發現膨潤處理過後的PAN 薄膜，在進行無電鍍處理後，並使銅離子擴散到基材內部且成核為Cu2-xS，且粒徑約為6 ~ 30nm，主要粒徑則為15 ~ 20nm。而且經過無電鍍處理後的PAN 薄膜，其抗菌效果明顯優於未經過無電鍍處理的PAN 薄膜。
並列摘要
Abstract In this investigation, the electroless plating method was used to plate the Cu31S16 and Cu2-xS on the surface and inner of the polyacrylontrile (PAN) for electromagnetic interference (EMI) shielding. In this plating procedure, the PAN film was swollen before electroless plating without sensitizing and activating pretreatment. Effects of operating parameters, cupric ion concentration and swelling pretreatment on the EMI (Electromagnetic Interference) shielding effectiveness (SE) were investigated. The EMI SE, surface morphology, cross section morphology, particles size inner the substrate, element of the layer and inner the substrate, thermal properties and antibacterial character of nano polymeric composites were detected by EMI, FE-SEM, HP-XRD, HR-TEM with EDX, EDS, DSC, AFM and antibacterial test analyzer, respectively. Experimental results revealed that the EMI shielding effectiveness of Cu31S16-PAN composites reached 18~20 dB when the plating temperature was 95℃ and plating time was 1 hour with cupric ion 0.48M, However, the EMI shielding effectiveness of composite reached 30~35 dB the PAN was pre-swelled before plating. HP-XRD analysis shows that the Cu31S16 was deposited on the PAN surface after the electroless copper plating procedure. In addition, AFM also shows that the Cu31S16 deposited on the PAN surface obviously. The surface morphology of Cu31S16-PAN and Cu31S16-SPAN were studied by FE-SEM. The grains shapes were likeness irregular and sharp on the substrate surface and the most thickness of the plating layer was about 200 nm. HR-TEM shows that the particles size of Cu2-xS compound distributed from 6 to 30 nm inner the SPAN substrate and the main particles size were about 15 to 20 nm. These nano polymeric composites possessed antibacterial character.