本研究的目的在於評估三個庫房作業，晶圓搬運、成品出貨及貨櫃裝填的下腰部負荷並提出改善方案。勞工因為搬運抬舉所引起的下腰部傷害的問題相當普遍，造成下腰部傷害主要的成因有工作姿勢不良、施力負荷過大及重複性施力等。針對這三個成因，本研究由實地了解工作現況著手，以OWAS及NIOSH1994來評估下腰部負荷的程度，瞭解問題之成因，再針對問題之成因，提出改善方案，最後再評估改善案的效益。
就改善前的現況，OWAS的分析顯示，這三個作業工作均有潛在的肌肉骨骼危害：OWAS介於AC1（沒有危害） 與AC3（有顯著危害）之間，但是沒有AC4（立即的危害）；NIOSH1994分析顯示，抬舉係數（lifting index, LI）介於1.3到3.0之間，有潛在危害，應加以改善。針對這些危害，本研究提出的改善構想，針對晶圓搬運是增加升降裝置及蝴蝶籠設計；成品出貨增設60公分作業平台；貨櫃裝填提供傾斜架，其共通的目的在於使作業員得以採行自然且省力的挺立站姿工作，以降低因為不良工作姿勢所引起的下腰部負荷。
改善結果顯示晶圓搬運的OWAS由AC1及AC2進步為AC1與AC1，NIOSH1994的LI由1.5與1.8進步為1.3及0.6；成品出貨OWAS由AC2及AC1進步為AC1與AC1，NIOSH1994的LI由2.0與1.3進步為0.9及0.9;貨櫃裝填作業經過改善可以省掉一個作業員，OWAS由AC3及AC3均進步為AC1，NIOSH1994的LI由2.4與3.0進步 1.0。整體而言，在簡單、低成本的改善下，下腰部的負荷有效的降低，這是個具有良好成效的改善案例，值得推廣。
關鍵字：下腰部負荷、OWAS、NIOSH1994

Abstract
The purpose of this study is to evaluate the lower back stress of three warehouse tasks, wafer transferring, product shipping, and container loading, and then propose improvement intervention. Wok-related musculoskeletal disorder is significant occupational problem, it main causes are awkward wotking posture, over-exertion, and repetitive motion. Toward these three causes, this study begins with the the understanding of current working situation, and base on current working situation, analyzing OWAS posture analysis and NIOSH 1994 lifting guide to coin out the contributing problem, then proposing improvement intervention, finally evaluation its cost-effectiveness.
Based on current working situation, OWAS analysis shows that these three tasks all have WMDS hazards, they range between AC1 (no hazard) and AC3 (potential hazard), but none of them are AC4 (prominent hazard): NIOSH 1994 lifting guide analysis shows that lifting index (LI) range between 1.3 and 3.0, there are potential hazard and need improvement. Toward these hazard problems, this study proposes improvement intervention: for wafer transferring, a lifting device and butterfly barrier are provided; for product shipping, a 60 cm high working surface is added; for container loading, a tilter is facilitated, the common purpose of these interventions are to induce the workers to adopt a natural and energy-saving erect standing posture to lessen the stress on the lower back due to awkward posture.
The result of improvement intervention shows that OWAS analysis for wafer transferring improves from AC1 and AC2 to AC1 and AC1, and NIOSH1994 analysis improves from LI of 1.5 and 1.8 to 1.3 and 0.6; OWAS for product shipping improves from AC2 and AC1 to AC1 and AC1, and NIOSH1994 improves from LI of 2.0 and 1.3 to 0.9 and 0.9; the intervention for container loading one of the two workers can be reduced, OWAS analysis of the improved task improves from AC3 and AC3 to AC1, no hazard, and NIOSH1994 improves from LI of 2.4 and 3.0 to 1.0. In summary, with simple and low cost intervention, the lower back stress can be effectively reduced, these improvement intervention case study are cost-effective, it promotion will be worthwhile.

Keywords：lower back stress、OWAS、NIOSH1994

目錄
摘要 i
Abstract ii
誌謝 iv
目錄 v
圖目錄 vii
表目錄 viii
第一章 緒論 1
1.1 研究背景 1
1.2 研究動機 1
1.3 研究目的 2
第二章 文獻探討 3
2.1 檢查表法 3
2.1.1肌肉骨骼傷害人因工程檢核表(MSDs) 3
2.1.2 REBA 快速全身評估方法 3
2.1.3人因工程基準線風險認定檢核表(BRIEF) 4
2.1.4 OWAS工作姿勢分析法 4
2.2 生物力學分析法 6
2.3 NIOSH1994抬舉工作指引 8
第三章 研究方法 11
3.1 現況說明 11
3.2 問題陳述 11
3.3 改善方案 12
3.4 評估改善績效 12
第四章 結果 14
4.1晶圓搬運改善案例 14
4.1.1 現況說明 14
4.1.2 問題陳述 14
4.1.3 改善方案 17
4.1.4 評估改善績效 18
4.2成品出貨改善案例 19
4.2.1 現況說明 19
4.2.2 問題陳述 20
4.2.3 改善方案 22
4.2.4 評估改善績效 23
4.3貨櫃裝填改善案例 24
4.3.1 現況說明 24
4.3.2 問題陳述 25
4.3.3 改善方案 27
4.3.4 評估改善績效 27
第五章 討論 29
第六章 結論與建議 30
6.1 結論 30
6.2 建議 30
參考文獻 32

參考文獻
中文部分
[1]張振平、陳志勇、游志雲、杜信宏，作業場所人體尺寸圖譜在現場應用之探討，行政院勞工委員會勞工安全衛生研究所，民國96年。
[2]葉文裕、林彥輝，工作現楊人因工程檢核表適用性之研究，行政院勞工委員會勞工安全衛生研究所，民國86年。
[3]張振平、陳志勇、游志雲，國人人體計測資料庫的更新與工作場所設施尺寸研究(1)~(3)，行政院勞工委員會勞工安全衛生研究所，民國94年。
[4]陳志勇、李開偉，攝影記者下背傷害評估研究，行政院勞工委員會勞工安全衛生研究所，民國90年。
[5]盧士一、葉文裕，下背部傷痛生物力學模式之評估研究，行政院勞工安全衛生研究所，民國90年。
[6]應宜雄、盧士一、陳志勇、李正隆，生物力學法人工抬舉姿勢評估圖之製作，行政院勞委會勞工安全衛生研究所，民國88年。
[7]李開偉、葉文裕、朱振群、陳志勇，半導體製造業累積性工作傷害現況調查，行政院勞工委員會勞工安全衛生研究所，民國86年。
[8]人因工程肌肉骨骼傷害預防指引，行政院勞工委員會勞工安全衛生研究所，民國90年。
[9]骨骼肌肉傷害人因工程檢核表使用手冊，行政院勞工委員會勞工安全衛生研究所，民國87年。
[10]人因工程應用手冊，行政院勞工委員會勞工安全衛生研究所，民國84年。
[11]工作現場人因工程檢點適用性研究，行政院勞工委員會勞工安全衛生研究所，民國86年。
[12]勞工下背痛預防研究三度空間動態模式之建立，行政院勞委會勞工安全衛生研究所，IOSH84-H323，民國84年。
[13]呂槃、李景美，台北市四種製造業勞工安全衛生知識、態度、習慣及教育訓練策略研究，行政院勞工委員會勞工安全衛生研究所，民國81年。
[14]江傳江、于邦基編譯，肌肉骨骼評估:基礎與技術，合記書局，民國92年。
[15]胡桓祥，應用人因工程工作姿勢圖例改善鑄造與錫錠回收工廠之工作現場，新竹市: 清華大學，碩士論文，民國96年。
[16]劉永福，以機能工作姿勢觀點進行麵包工廠之工作場所改善，新竹市: 清華大學，碩士論文，民國96年。
[17]張清忠，半導體機台人因工程安全檢核表設計與評估探討，高雄醫學院碩士論文，民國88年。
英文部分
[18]Barnes, R.M.,1980,“Motion and time Study“,Design and Measurement of Work,7th edition,John Wiley & Sons.
[19]Bruijn,L., Engels,J.A., and Gulden,J.W.J.,1998,“A Simple Method to Evaluate the Reliability of OWAS Observations”,Applied Ergonomics, 29(4):pp.281-283.
[20]Chaffin,D.B.,and Andersson,G.B.J.,and Martin,B. J.,1999,”Occupational Biomechanics,3rd Ed.”,John Wiley & Sons
[21]Chen,Y.L.,2000,“Changes in lifting dynamics after localized arm fatigue”,International Journal of Industrial Ergonomics,Vol.25,pp.611-619.
[22]Dedobbeleer N.,German P.,1987,“Safety Practices in Construction Industry”,59 Journal of Occupational Medicine,29 (11):pp.863-868.
[23]Gagnon,M.,Delisle,A.,and Desjardins,P.,2002,“Biomechanical differences between best and worst performances in repeated free asymmetrical lifts”,International Journal of Industrial Ergonomics,Vol.29,pp.73-83.
[24]Graham,B.,Nicola,R.,1996“Working Practices in a Perchery System,Using the Ovako Working Posture Analyzing System”,Applied Ergonomics,27(4):pp.281-284.
[25]Green,L.W.,Kreuter,M.W.,Deeds,S.G., and Partridge,K.B.,1980,“Health Education Planning: A Diagnostic Approach”,Palo Alto,CA:Mayfield Publishing Co..
[26]Karhu,O.,Kansi,P.,and Kuorinka,I.,1977“Correcting Working Postures in Industry: A Practical Method for Analysis”,Applied Ergonomics,8(4):pp.199-201。
[27]Karhu,O.,Harkonen,R.,Sorvali,P., and Vepsalainen,P.,1981,“Observing Working Postures in Industry: Examples of OWAS Application”,Applied Ergonomics,12(1):13-17.
[28]Li,K.W.,Lee, C.L.,“Postural Analysis of Four Jobs on Two Building Construction Sites: an Experience of Using the OWAS Method in Taiwan”, J.Occup.Health,41:pp.183-190.
[29]Lynn McAtamney and E.Nigel Corlett,1993,“RULA: a survey method for the investigation of related upper limb disorders“Applied Ergonomics, 24 (2),pp.91-99.
[30]Meyers,F.E.,1992,“Motion and Time Study“,Improving Work methods and Management,Prentice Hall.
[31]National Institute for Occupational Safety and Health,1981,A Work Practices Guide for Manual Lifting,Technical Report. U.S. Dept. of Health and Human Services, Cincinnati, OH,pp.81-122.
[32]Niebel,B. and Freivalds,A.,1999. Methods,“Standards and Work Design“,10th edition,McGraw-Hill.
[33]NIOSH,2000,“Elements of Ergonomics Programs“,National Institute of Occupational Safety and Health,http://www.cdc.gov/niosh/
[34]Occupational Safety and Health Administration,1995,“Draft: Instructions for Completing the Risk Factor Checklist“,pp.24-32.
[35]OSHA,2000,“Ergonomics: The Study of Work“,U.S. Department of Labor Occupational Safety and Health Administration.
[36]Perkio-Makela,M.,and Hentila,H.,2005,“Physical work strain of dairy farming in loose housing barns”,International Journal of Industrial Ergonomics,Vol.35,pp.57-65.
[37]Plamondon,A.,Gagnon,M.,and Desjardins,P.,1996,“Validation of two 3-D segment models to calculate the net reaction forces and moments at the L5/S1 joint in lifting”,Clinical Biomechanics,Vol.11,pp.101-110.
[38]Pulat,B.M., 1992.“Fundamentals of Industrial Ergonomics“,Prentice Hall.
[39]Sanders,M.S.and McCormick,E.J.,1993,“Human Factors in Engineering and Design“,7th edition,McGraw-Hill.
[40]Wu,S.P.,2003,“Maximum acceptable weights for asymmetric lifting of Chinese females”,Applied Ergonomics,Vol.34,pp.215-234.
[41] Hignett, S. and McAtamney, L., “Rapid entire body assessment (REBA),”Applied Ergonomics, Vol. 31, pp. 201-205, 2000.