製備顆粒型聚偏二氟乙烯薄膜及薄膜蒸餾之應用

Preparation of particulate polyvinylidene fluoride membranes and their application in membrane distillation processes

楊承道(Cheng-Dau Yang)

指導教授 ： 鄭廖平

淡江大學/工學院/化學工程與材料工程學系碩士班/碩士(2015年)

https://doi.org/10.6846/TKU.2015.00272

摘要

DMF/PVDF 製膜液融解在不同溫度(50、60、70 和80 oC)，浸入正辛醇沉澱槽，製備出多孔型PVDF 薄膜，其代號分別為FO50、FO60、FO70 及FO80，薄膜結構對稱，結晶顆粒尺寸均一，孔洞與孔洞互通貫穿整張薄膜。當製膜液融解溫度為50 oC，顆粒尺寸只有1um，相對的當融解溫度為提高至80 oC，顆粒尺寸成長到2um。四種薄膜孔隙度為66%，結晶度55%，接觸角133o(上表面)、126o(下表面)，抗張強度隨著顆粒尺寸增加而降低，因為顆粒間的連結減少所造成。薄膜測試直接接觸式薄膜蒸餾(DCMD)，其阻隔率大於99%，操作條件：3.5 wt%NaCl(aq)；Tfeed = 52 oC；Tproduct = 18 oC；進料與產物流速皆為0.7 L/min；FO60、FO70 及FO80 有較高的通量(12、14、16 LMH)，然而FO50 通量只有2.7 LMH。當進料溫度或流速提升，通量也隨之提高。另一方面增加NaCl 氯化鈉水溶液濃度，通量下降。FO60 薄膜測試DCMD 48 小時，通量從11.6 降低至10.5 LMH，阻隔率仍維持在99%以上。DMF/PVDF 製膜液融解在不同溫度(50、60、70 和80 oC)，浸入正辛醇沉澱槽，製備出多孔型PVDF 薄膜，其代號分別為FO50、FO60、FO70 及FO80，薄膜結構對稱，結晶顆粒尺寸均一，孔洞與孔洞互通貫穿整張薄膜。當製膜液融解溫度為50 oC，顆粒尺寸只有1um，相對的當融解溫度為提高至80 oC，顆粒尺寸成長到2um。四種薄膜孔隙度為66%，結晶度55%，接觸角133o(上表面)、126o(下表面)，抗張強度隨著顆粒尺寸增加而降低，因為顆粒間的連結減少所造成。薄膜測試直接接觸式薄膜蒸餾(DCMD)，其阻隔率大於99%，操作條件：3.5 wt%NaCl(aq)；Tfeed = 52 oC；Tproduct = 18 oC；進料與產物流速皆為0.7 L/min；FO60、FO70 及FO80 有較高的通量(12、14、16 LMH)，然而FO50 通量只有2.7 LMH。當進料溫度或流速提升，通量也隨之提高。另一方面增加NaCl 氯化鈉水溶液濃度，通量下降。FO60 薄膜測試DCMD 48 小時，通量從11.6 降低至10.5 LMH，阻隔率仍維持在99%以上。

關鍵字

顆粒型薄膜 ； 直接接觸式薄膜蒸餾 ； 聚偏二氟乙烯

並列摘要

Microporous PVDF membranes were prepared by immersion-precipitation
of DMF/PVDF solutions dissolved at different temperatures (50, 60, 70, and 80
oC) in 1-octanol bath. The membranes formed (termed FO50, FO60, FO70, and
FO80) exhibited a symmetric structure, consisting of nearly equal-sized
crystalline particles that interlinked into a continuous matrix, in which porous
channels dispersed. When the dope was dissolved at 50 oC, the particles were
only ~1 micron; in contrast, the particles expanded significantly to ~3 microns,
if dissolution was carried out at 80 oC. All membranes had a similar porosity of
~66%, crystallinity of ~55%, and water contact angles of 133o (top surface) and
126o (bottom surface). The tensile strength decreased with increasing particle
size, due to reduced and particle-particle interconnection. The membranes were
tested for performance in desalination via direct contact membrane distillation
(DCMD). High rejections (> 99%) were attained for all membranes operated
under the conditions: feed concentration = 3.5% NaCl(aq), Tfeed = 52 oC, Tproduct
= 18 oC, and circulation rates = 0.7 L/min for both feed and product streams.
The permeation fluxes for the membranes FO60, FO70, and FO80 reached high
IV
values of 12, 14, and 16 LMH, respectively; however, that for FO50 was only
2.7 LMH, consistent with the morphologies of these membranes. As the feed
temperature or the circulation rate was raised, the permeation flux increases as
well. On the other hand, raising the salt concentration in the feed caused
decrement of the permeation flux. For the membrane FO60 operated over the
period of 48 h., the flux decreased slightly from 11.6 to 10.5 LMH, rejection
>99%.

並列關鍵字

particulate membrane ； DCMD ； PVDF

參考文獻

1. M. Khayet, Membranes and theoretical modeling of membrane distillation: a review, Adv. Colloid Interface Sci. 164 (2011) 56–88.

2. G.Q. Guan, R. Wang, F. Wicaksana, X. Yang, A.G. Fane, Analysis of membrane distillation crystallization system for high salinity brine treatment with zero discharge using Aspen flowsheet simulation, Ind. Eng. Chem. Res. 51 (41) (2012) 13405-13413

3. Lucy Mar Camacho, Ludovic Dumee, Jianhua Zhang, Jun-de Li, Mikel Duke, Juan Gomez, Stephen Gray, Advances in membrane distillation for water desalination and purification applications, Water 5 (2013) 94-196.

4. Jing Zhang, Zhenyu Song, Baoan Li, Qin Wang, Shichang Wang, Fabrication and characterization of superhydrophobic poly(vinylidene fluoride) membrane for direct contact membrane distillation, Desalination 324 (2013) 1-9.

5. A.S. Kim, A two-interface transport model with pore-size distribution for predicting the performance of direct contact membrane distillation (DCMD), J. Memre. Sci. 428 (2013) 410-424.