Journal of Applied Science and Engineering

Published by Tamkang University Press

1.30

Impact Factor

2.10

CiteScore

Ziwei Zhang This email address is being protected from spambots. You need JavaScript enabled to view it.1, Guoying Meng1 and Aiming Wang1

1School of Mechanical Electronic and Information Engineering, China University of Mining and Technology (Beijing), Beijing 100083, P.R. China


 

Received: March 7, 2018
Accepted: April 16, 2018
Publication Date: June 1, 2018

Download Citation: ||https://doi.org/10.6180/jase.201806_21(2).0001  

ABSTRACT


To study the process of coal mine drainage pipe scale removal by using a water jet and its affecting parameters, a numerical model based on the fluid-solid interaction method is developed to simulate the removal process. The grid of the water jet and null material adopts ALE (Arbitrary Lagrange-Euler) formulation, while the pipe scale grid employs Lagrange formulation. The water jet penetration is simulated by coupling ALE fluid elements and Lagrange solid elements. The stress variation inside the pipe scale under the impact of water jet is analyzed. In addition, the effect of water jet parameters on the cutting depth is investigated. The numerical results are consistent with the experimental results. The results illustrate that the impact velocity and the incident angle of water jet have a significant influence on the impact depth determination. Small impact velocity causes erosion near the pipe scale surface and the actual crush occurs only when the velocity exceeds a certain value. The incident angle of water jet has an efficient range and larger cutting depths can be obtained as the incident angle increases up to 70°.


Keywords: Drainage Pipe Scale, Water Jet, ALE, Lagrange, Stress Variation, Cutting Depth


REFERENCES


  1. [1] Vijaykumar, R., Julie, M. J., Vieira, A. T., Humphrey, J. and Zheng, D., “Startup and Shutdown Steam Generator Separator Piping Forces for a Coal-fired Supercritical Power Plant,” Proc of the ASME 2012 Pressure Vessels and Piping Conf, Toronto, Ontario, Vol. 3, pp. 7011707 (2012). doi: 10.1115/PVP2012-78798
  2. [2] Han, Q. Y., Peng, X. and Yang, Y. P., “Influence of Emulsion on the Corrosion and Scaling on Pipelines of Cooling SystemDeep Coal Mine: a Experiment Study,” Advanced Materials Research, Vol. 902, No. 3, pp. 105110 (2014). doi: 10.4028/www.scientific.net/ARM. 902.105
  3. [3] Lu, Y. Y., Huang, F., Wang, J. H. and Liu, X. C.,“Analysis of Stress Wave Effect During Rock Breakage Process by Ultra-high Pressure Water Jet,” Journal of China University of Mining &Technology, Vol. 42, No. 4, pp. 519525 (2013).
  4. [4] Wang, C. J., “Design of Pipe Scale Removal Robot for Coal Mine Pipe,” Coal Mine Machinery, Vol. 30, No. 8, pp. 2426 (2009). doi: 10.13436/j.mkjx.2009.08. 050
  5. [5] Hsu, C. Y., Liang, C. C., Teng, T. L. and Nguyen, A. T., “A Numerical Study on High-speed Water Jet Impact,” Ocean Engineering, Vol. 72, No. 1, pp. 98106 (2013). doi: 10.1016/j.oceaneng.2013.06.012
  6. [6] Junkar, M., Jurisevic, B., Fajdiga, M. and Grah, M., “Finite Element Analysis of Single-particle Impact in Abrasive Water Jet Machining,” Int. J. Impact Eng., Vol. 32, No. 2, pp. 10951112 (2006). doi: 10.1016/j. ijimpeng.2004.09.006
  7. [7] Lebar, A. and Junkar, M., “Simulation of Abrasive Waterjet Machining Based on Unit Event Features,” Proc. Inst. Mech. Eng. B. J. Eng. Manuf., Vol. 217, No. 25, pp. 699703 (2003). doi: 10.1243/095440503322 011425
  8. [8] Chahine, G. L. and Kalumuck, K. M., “The Influence of Structural Deformation on Water Jet Impact Loading,” J. Fluids Struct., Vol. 12, No. 1, pp. 103121 (1998). doi: 10.1006/jfls.1997.0127
  9. [9] Lu, Y. Y., Huang, F., Liu, X. C. and Ao, X., “On the Failure Pattern of Sandstone Impacted by High-velocity Water Jet,” Int. J. Impact Eng., Vol. 76, No. 3, pp. 6474 (2015). doi: 10.1016/j.ijimpeng.2014.09.008
  10. [10] Lee, J. H., Park, K. S., Kang, M. C., Kang, B. S. and Shin, B. S., “Experiments and Computer Simulation Analysis of Impact Behaviors of Micro-sized Abrasive in Waterjet Cutting of Thin Multiple Layered Materials,” Trans. Nonferrous Met. Soc. China, Vol. 22, No. 3, pp. 864869 (2012). doi: 10.1016/S1003-6326(12) 61817-2
  11. [11] Tang, Y., Chan, D. H. and Zhu, D. Z., “Numerical Investigation of Sand-bed Erosion by an Upward Water Jet,” J. Eng. Mech., Vol. 143, No. 9, pp. 114 (2015). doi: 10.1061/(ASCE)EM.1943-7889.0001319
  12. [12] Li, G. S., Liao, H. L., Huang, Z. W. and Shen, Z. H., “Rock Damage Mechanisms under Ultra-high Pressure Water Jet Impact,” Journal of Mechanical Engineering, Vol. 45, No. 10, pp. 284293 (2009). doi: 10.3901/JME. 2009.10.284
  13. [13] Jiang, H. X., Liu, Z. H. and Gao, K. D., “Numerical Simulation on Rock Fragmentation by Discontinuous Water-jet Using Coupled SPH/FEA Method,” Powder Technol., Vol. 312, No. 10, pp. 248259 (2015). doi: 10.1016/i.powtec.2017.02.047
  14. [14] Song, S. X., Tian, G. T. and Yu, D. Q., “Fracture Mechanism of Radial Tyre Rubber under Ultra-high Pressure Water Jet Impact,” Journal of Mechanical Engineering, Vol. 50, No. 12, pp. 3643 (2014). doi: 10. 3901/JME.2014.12.036
  15. [15] Aganin, A. A. and Khismatullina, N. A., “Features of Deformation of Metal Body Surfaces under Impact of a Water Jet,” Journal of Physics Conference Series, Vol. 669, No. 2, pp. 14 (2016). doi: 10.1088/17426596/669/1/012031
  16. [16] Brunton,J.H.,“HighSpeedLiquidImpact,”Phil.Trans. A, Vol. 260, No. 3, pp. 7985 (1966). doi: 10.1088/ 1742-6596/669/1/012031
  17. [17] Ahmed, D. H., Naser, J. and Deam, R. T., “Particle ImpactCharacteristicson CuttingSurface During theAbrasive Water Jet Machining: Numerical Study,” J. Mater. Process. Technol., Vol. 232, No. 10, pp. 116130 (2016). doi: 10.1016/j.jmatprotec.2016.01.032
  18. [18] Li,R.,Ninokata, H. and Mori,M.,“ANumericalStudy of Impact Force Caused by Liquid Droplet Impingement onto a Rigid Wall,” Prog. Nucl. Energy, Vol. 53, No. 10, pp. 881885 (2011). doi: 10.1016/j.pnucene. 2011.03.002
  19. [19] Aquelet, N., Souli, M. and Olovsson, L., “Euler-Lagrange Coupling with Damping Effects: Application to Slamming Problems,” Comput. Methods Appl. Mech. Engrg, Vol. 195, No. 9, pp. 110132 (2006). doi: 10. 1016/j.cma.2005.01.010
  20. [20] Sheng, D. C., Nazem, M. and Carter, J. P., “Some Computational Aspects for Solving Deep Penetration Problems in Geomechanics,” Comput. Mech., Vol. 44, No. 10, pp. 549561 (2009). doi: 10.1007/s00466-0090391-6
  21. [21] Souli, M. and Shahrour, I., “Arbitrary Lagrangian Eulerian Formulation for Soil Structure Interaction Problems,” Soil Dynamics and Earthquake Engineering, Vol. 35, No. 3, pp. 7279 (2012). doi: 10.1016/j.soildyn. 2011.10.006
  22. [22] Kim, J. H. and Shin, H. C., “Application of the ALE Technique for Underwater Explosion Analysis of a Submarine Liquefied Oxygen Tank,” Ocean Engineering, Vol. 35, No. 10, pp. 812822 (2008). doi: 10. 1016/j.oceaneng.2008.01.019
  23. [23] Movahhedy, M. R., Gadala, M. S. and Altintas,Y., “Simulation of Chip Formation in Orthogonal Metal Cutting Process: an ALE Finite Element Approach,” Machining Science and Technology, Vol. 1091, No. 344, pp. 1545 (2000). doi: 10.1080/10940340008945698