等通道轉角擠型製程對鎂-5錫-1鈣合金抗潛變性質的影響

Effect of Equal Channel Angular Extrusion on the Impression Creep Behavior of Mg-5Sn-1Ca Alloy

曾奕憲(Yi-Shian Tzeng)

指導教授 ： 劉增豐

國立交通大學/工學院/材料科學與工程系所/碩士(2012年)

https://doi.org/10.6842/NCTU.2012.00813

摘要

本實驗係以重力澆鑄法製成Mg-5wt.%Sn-1wt.%Ca之鎂合金鑄錠，其平均晶粒大小約為150μm，其主要析出相為Mg2Sn和CaMgSn。將實驗合金於250℃下經ECAE製程後，以OM觀察其顯微組織，並以Instron 8501萬能試驗機測試其高溫潛變性質。
研究結果顯示，經過不同道次ECAE製程的實驗合金，其應力指數n隨著擠型次數的增加有下降的趨勢，從鑄態的n=7.7到擠型四道次的n=5.68，這意味著經ECAE製程後，實驗合金的潛變主導機制從power-law break down的區域漸漸移向晶界滑移區(Grain Boundary Sliding)。
經由ECAE後活化能從鑄態的148.2KJ/mol下降到N=4的95.8KJ/mol，意味著材料擴散機制隨著擠製道次的增加，從差排的滑移轉變為晶界擴散。
抗潛變性質方面，分別在N=1和N=4有最好和最差的抗潛變性質，以溫度200℃，施加應力為350MPa的情況來說，N=1的潛變速率為5.4E-4，遠低於N=4的1.24E-3，這是由於潛變機制朝向晶界滑移，使得具有較小晶粒，更多晶界的N=4合金自然具有較N=1合金差的抗潛變性質。

關鍵字

鎂合金 ； 潛變性質 ； 鎂-5錫-1鈣

並列摘要

In this research, the effect of equal channel angular extrusion (ECAE) on the impression creep behavior of magnesium alloy (Mg-5wt.%Sn-1wt.%Ca) was investigated. Energy dispersive system (EDS) was used for chemical composition analysis. The precipitation phases confirmed by X-ray diffraction pattern (XRD) were Mg2Sn and CaMgSn. The microstructures were examined by optical microscopy (OM). Instron 8501 was used for impression creep test.
The stress exponent decreases from n=7.7 for the as-cast sample to n=5.68 for the sample after four passes of ECAE process (N=4). It suggests that the dominant creep mechanism of alloy changes from power-law breakdown region to grain boundary sliding region.
The creep activation decreases from 148.2KJ/mol for the as-cast sample to 95.8KJ/mol for N=4 sample. It suggests that the dominant diffusion mechanism of alloy changes from dislocation slip to grain boundary diffusion.
When the applied stress is 350MPa at 200℃, N=1 sample has the best creep resistance. Its creep rate is 5.4E-4. Under the same test condition , the N=4 sample has the worst creep resistance. Its creep rate is 1.24E-3. It's because of the change of dominant creep mechanism. The N=4 sample has the smallest gains, which means the most grain boundaries, so its creep resistance is worse than the others.

並列關鍵字

Mg alloy ； creep behavior ； Mg-5Sn-1Ca

參考文獻

1. 林哲毅,「ZA85鎂合金經等通道轉角擠型後顯微組織與機械性質改善之研究」, 國立交通大學材料科學工程研究所碩士論文, 2009.

4. A. Sanschagrin, R. Tremblay, R. Angers, D. Dube, “Mechanical properties and microstructure of new magnesium-lithium base alloys”, Materials Science and Engineering, A220, 1996, pp. 69-77.

5. Yan Jingli, et al., “Creep behavior of Mg–2 wt.%Nd binary alloy”, Materials Science and Engineering , A524, 2009, pp. 102–107.

6. Z. Zhang, A. Couture, A. Luo, “An Investigation of the Properties of Mg-Zn-Al Alloys”, Scripta Materialia, Vol.39, No.1, 1998, pp. 45-53.

8. Hongmei Liu, et al., “The microstructure, tensile properties, and creep behavior of as-cast Mg-(1-10)%Sn alloys”, Journal of Alloys and Compounds, 440, 2007, pp. 122-126.